CISCO MDS 9124 CONFIGURATION GUIDE PDF

Zulkizilkree I am not sure. In this case, using the proxy initiator mode simplifies the configuration. FCIP uses different ports. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur. Then states two bullets later: If you assign port number for physical portshow can you assign for ports?

Author:Teshakar Kazizil
Country:Switzerland
Language:English (Spanish)
Genre:Photos
Published (Last):15 March 2013
Pages:279
PDF File Size:3.99 Mb
ePub File Size:19.31 Mb
ISBN:384-9-24538-914-6
Downloads:77203
Price:Free* [*Free Regsitration Required]
Uploader:Mezinris



Vozuru This page incorrect states that fcns reject-duplicate-pwwn is disabled by default. Should say Step 1 Enable the mgmt 0 interface. You do not need to restart the fcdomain. This situation can require several configuration tasks confuguration each iSCSI host. The default authentication port is Cisco Documentation team has internally re-written this as: This is not correct. This page incorrectly states that you can disable password verification with aaa authentication login none command.

You basically give the same settings for the IBM blade switch but this is a 24 port not a 20 port. This is not correct as this does not work. If a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated.

Reconfiguration as in changing of domains is always disruptive. The autoreconfigure option takes immediate effect at runtime. Page Figure shows incorrect ip default-gateway Page States in one bullet: Have a few different people read that and I think you will see where I am coming from. Testing indicates that this is in fact enabled by default.

On the same page I find this block of text very vague and confusing: You can nondisruptively reconfigure the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap. This is configuation true. These pages talk about an active mode of fcanalyzer. Page shows with 8 base ports 8 licensed for growth.

A disruptive reconfiguration may affect data traffic. If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration. FCIP uses different ports.

When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: This should be made more clear. If you assign port number for physical portshow can you assign for ports?

You must be logged in to post a comment. Should be 8 base ports, which can goto 8 or 16 additional ports. Leave a Reply Cancel reply You must be logged in to confighration a comment. You cannot mix ingress and egress interfaces in the same SPAN session. The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite. I am not sure if this is valid.

Previous blog entries also dealt with storage, compute, virtualization and professional services. This is very redundant and can be combined into one bullet. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur. From time to time I will blog about other things of interest. Although it can be configured it has no effect.

Page Information is repeated twice on the same page: Caution The span drop-threshold can be changed only if no span sessions are currently active on the switch.

This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces confjguration FCIP tunnels to go along with the Network Simulator. Obviously there was a part of this paragraph that got chopped off somewhere.

This blog is mostly about my pursuits in Data Science. I am not sure. It is worded as if it is a requirement but it is in fact not. Then states two bullets later: In this case, using the proxy initiator mode simplifies the configuration.

I am not sure that the statement in bold is correct. TOP 10 Related.

ANTAGONISTAS NICOTINICOS PDF

Preview Tool

Vozuru This page incorrect states that fcns reject-duplicate-pwwn is disabled by default. Should say Step 1 Enable the mgmt 0 interface. You do not need to restart the fcdomain. This situation can require several configuration tasks confuguration each iSCSI host.

PSICOLOGIA BIOLOGICA JAMES KALAT PDF

Cisco Cisco mds 9124 - fabric switch Manuals

.

LA GRAMMATICA DELLA MUSICA OTTO KAROLYI PDF

CISCO MDS 9124 CONFIGURATION GUIDE PDF

.

RAMSUKHDASJI BOOKS PDF

How to configure an external Cisco MDS 9124 Switch

.

Related Articles